Controller Tester

This free controller tester lights up every button, trigger and stick the moment you press it. Use it as a quick gamepad tester before a match, after a repair or when a button feels off.

Connect your controller and press any button.

Controller diagram. Pressed inputs light up.

0 of 19 inputs tested

Sticks

Left X 0.00 Y 0.00
Right X 0.00 Y 0.00

Triggers

LT
0.00
RT
0.00

Buttons

Face
  • A
  • B
  • X
  • Y
Shoulder
  • LB
  • RB
  • LT
  • RT
D-pad
  • Up
  • Down
  • Left
  • Right
Menu
  • View
  • Menu
  • Home
Clicks
  • LS
  • RS
Raw data

Connect a controller to list every button and axis it reports.

How to use the controller tester

  1. Connect your controller. Plug in the USB cable or pair it over Bluetooth.
  2. Press any button. Browsers keep a controller hidden until it sends an input, so the page wakes up on your first press.
  3. Try every input. Press each button, pull both triggers and roll both sticks in a full circle. Each input gets a tick once the page has seen it.

This is the fastest way to test controller inputs one by one. When the counter is full, the controller tester has seen every input at least once.

What this gamepad tester checks

Whether you call it a gamepad tester or a joypad tester, the job is the same: show what the controller really sends.

  • Buttons Face buttons, bumpers, stick clicks and menu buttons, each shown as pressed or released.
  • D-pad All four directions, including diagonals.
  • Triggers How far each trigger travels, from 0.00 to 1.00.
  • Sticks The position of both sticks on each axis, from −1.00 to 1.00.

Under the diagram, the raw list works as a controller input test: it shows every button and axis your controller reports, including paddles and touchpads the diagram does not draw. The controller tester reads up to four controllers at once; switch between them with the numbered tabs.

Reading your results

  • A button reads 0 when released and 1 when pressed. If it flickers while you hold it, or never lights up, the contact under it is worn or dirty.

  • Triggers should climb smoothly from 0.00 to 1.00. A trigger that stops at 0.90 will not give full throttle or full brake in a racing game.

  • A stick you let go of should settle close to 0.00 on both axes. A small leftover is normal and games ignore it. If the number keeps moving while your thumb is off the stick, that is drift. The controller tester shows it, and the stick drift test measures exactly how much.

Controller not detected?

Work through these in order.

  1. Press a button. The page cannot see a controller that has not sent an input yet.
  2. Try another cable or port. Some USB cables only carry power.
  3. Pair it again. Remove the controller from your Bluetooth devices, then pair it from scratch.
  4. Close other apps that use it. A game launcher or remapping tool can keep the controller to itself.
  5. Try another browser. If the page still shows nothing, open it somewhere else to rule the first browser out.

If your computer or phone does not list the controller either, the fault is in the controller or the cable, and no online controller checker can see it.

Supported controllers and browsers

This page works as a game controller tester for any device your operating system recognises: Xbox, PlayStation and Switch pads, third-party controllers and older USB joypads. It is a joystick tester too. Flight sticks, racing wheels, pedals and arcade sticks appear in the raw list with every axis they report, so you can run a joystick test without extra software.

You need a current version of Chrome, Edge, Firefox or Safari. The table shows what your own browser allows right now.

In this browserStatus
Reading controllersChecking…
Secure connectionChecking…
VibrationConnect a controller to check

More controller tests

The main controller test covers every input. These tools go deeper on one thing each.

Frequently asked questions

Does it work on a phone or tablet?

On most recent phones and tablets, yes. Pair the controller over Bluetooth, open this page and press a button.

Why do I have to press a button first?

Browsers hide controllers from websites until the controller sends an input. That stops a page from identifying your hardware without you doing anything. One press is enough.

Is anything uploaded?

No. Your inputs are read and drawn inside your browser and are never sent to a server.

Why does my controller show a different name with Steam open?

Steam can sit between the controller and other programs and present it as a generic Xbox-style pad. Close Steam, reconnect the controller and run the gamepad test again to see the real device.

Is this controller tester free and safe?

Yes. It is free and needs no download or account. The page only reads the inputs your browser hands it. It cannot change settings or firmware on your controller.